Can I Set Up A Tub Myself?
Can I Set Up A Tub Myself?
Blog Article
Presented here below you can get a bunch of excellent advice in relation to How to Install a Bathtub Yourself.
Setting up a bathtub isn't specifically brain surgery, yet it does need solid plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately hard job. If the old tub is conveniently available, the job can relocate easily; if you have to open a wall surface to remove the old tub as well as position the brand-new bathtub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have qualified on your own for the task and also are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is better to think about employing one before you start. Possibilities are you might need a professional plumber to make tube links.
This article will certainly help you mount a new bath tub in your restroom if you have actually already acquired a new bathtub as well as do not require to alter the setup of your previous supply of water pipelines.
Your tools and also material checklist need to comprise the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is usually the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a towel ready for the remaining water that will certainly originate from the pipes. When the supply pipelines have actually been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the placing opening in the bath/basin making certain that the washers are in place between the tap as well as the sink. Safeguard the faucet in place with the supplier given backnut. As soon as the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The former kind needs to be connected to the tap finishes initially, tightening up only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Using the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 little factors.
The following goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bathtub until the level reviews degree.
To set up taps, fit the bottom of the furthest flexible faucet adapter to the proper supply pipeline by making a compression join; then do the same for the various other faucet.
Turn on the water system as well as check all joints and brand-new pipework for leakages as well as tighten them if required. Load the bath tub as well as also check the overflow electrical outlet as well as the typical outlet for leaks.
Ultimately, deal with the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait up until the bathtub has actually been utilized at least once as this will certainly settle it into its last setting.
Preparing for the Installment
First of all, the supporting structure provided with the bath needs to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps unit to avoid strain on the bath tub.
Fit the flexible faucet ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack a stiff seal, causing the water to permeate the wall surface between the bath and also the tiling, leading to problems with moisture and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can securing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly load the bath tub with water prior to sealing, to allow for the motion experienced when the bathtub remains in usage. The sealer can split relatively early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our article about A Step-by-Step Guide to Installing a Bathtub. Thank you for taking the time to browse our article. Do you know about anybody else who is occupied with the topic? Take a moment to share it. Thank you for going through it.
Visit Page
Report this page